#Remotesight port install#
#Remotesight port windows 10#
#Remotesight port windows#

I also tried to disconnect one path from remotesite to core to see if there is a problem with it but still not working - and as said - different device with the same setup works. I tried various vlans/roles but they dont seem to get a connection. but it does get an IP from the dhcp and it is shown in the dashboard. The device what is not working on the remote site is working when connected to a switch which is connected L2 to my Cores and they have a L2 connection to the controllers.Īnother device is NOT working on the remote site with the same vlan, same tunnel, same switch. To clarify - my setup uses OSPF routing as well. But with port-based I dont use 802.1x so there is nothing to care about, is it? Strangely I can get an IP and I see my wired laptop in the dashboard of the MC.

#Remotesight port windows#

But its not with another device nor with my windows laptop. What looks strange to me is that there is no TX. Other devices in that vlan are pingable when connected to WiFi (same role).Īnd I changed the controller IP to the primary/backup but it didnt change anything unfortunately. Clients get the right IP and everything, but they cant get anywhere nor can I ping them. Yes I figured that but I am using 'port-based'. When I use same vlan, same role with Wifi I can ping everything - well whatever my firewall allows in said vlan. It looks like RX packets are coming to the controller but TX is 0. DHCP server and gateway is the same but I cannot ping it.

Vlan is on the switch (no uplink, no IP) and controller and I get a DHCP address from my network. 2 MDs clustered, the tunneled-node server IP is the VRRP of the mgmt IP.

I am trying to get a tunneled-node per port working and it is not looking too bad actually but something is missing. You'll need to point the switch to a physical IP of the gateway or cluster, virtual IPs are not supported as a gateway IP for user-based tunneling. Please let us know if this has been useful for you in the comments below and we will add more troubleshooting techniques in future.Subject: Tunneled-Node - Client gets DHCP but cannot access anything These commands and techniques are very useful when you are troubleshooting a network. TcpTestSucceeded will give you True if the port is open and false if the port is closed. The TNC command will give you basic information about the network connection like computer name, IP address, Interface through which you are connecting, source IP, whether the ping is successful or not, Ping reply time and finally TcpTestSucceeded. You can specify the port number using the -port switch at the end of tnc command. You can also put an IP address instead of the host name. Tns is short for Test-NetworkConnection command. Tnc -port 80 Checking open port using PowerShell

Open PowerShell by going to Run –> powershell.

Let’s check whether a remote network port is open and listening or not. Since Microsoft is pushing PowerShell and CMD has become a legacy system, we should be using PowerShell for most of our working.

If you receive “ Connection to host lost“, this means that the port is open but the host is not accepting new connections. If you receive “ Could not open connection” or a blank screen with blinking cursor, this means the port is closed. If you receive “ Press any key to continue” prompt, this means that the port is open and responding to telnet. You should replace 80 with you desired port number. 80 is the port number which you want to probe. You can also put an IP address instead of the name.

Open Telnet using the three steps described above and issue the following command: To check the network port, follow the instructions below:

Go to Run –> telnet Check whether the port is open or not using Command Prompt.

#Remotesight port install#

To install Telnet, follow the instructions below: If you are going strictly with a DOS based command then you are left with no option but to install telnet in Windows 10. Portqry used to be the command of choice for checking remote ports being alive and listening but it was only available up till Windows XP and Windows Server 2003. Even DOS Command Prompt has also become secondary with PowerShell taking the center stage.

#Remotesight port windows 10#

Windows 10 does not come with Telnet pre-installed.

Check whether the port is open or not using Command Prompt.